Cannons UK Rubber Square Gym Mats 40cm x 40cm x 20cm
NOW REDUCED TO JUST £3.29 A TILE
Cannons UK is a preferred partner in constructing children's and sports playgrounds, recreation centres and sports fitness equipment for open areas.
Cannons UK is our trademark that ensures safety, hygiene, quality and is the right choice for the covering of your venue.
Our goal is to provide the best solutions for shock, heat and moisture resistance. Cannons UK rubber tiles can be used in severe conditions due to their high durability.
Cannons UK Tiles, retain their shape and characteristics for years without any change. Weather conditions (cold, warm, humid etc.) do not change the shape.
These products are durable, lightweight and also have a high shock absorption, slip resistance to prevent injuries. The surface of the tile prevents people's fatigue. EPOS tiles are lighter than other material and significantly less expensive. Rubber tiles are adhered to the floor with EPOS two-component polyurethane adhesive.
40cm x 40cm x 20cm (30mm and 40mm thickness also available.)
- Children's playgrounds
- Sports facilities
- School playgrounds
- Fitness centres
- Terraces etc....
- Prevents fatigue
- Stops Moisture's
- Resistance to abrasions
- Contains UV particles for outside climate conditions
Tested to TS EN1176-1 and TS EN 1177
Critical Fall Heights
20mm – 136cm
30mm – 159cm
40mm – 187cm
Installation with EPOS Two-component Polyurethane Adhesive
Inspect delivered rubber tiles thoroughly. Any visual defects must be reported prior to installation.
Store tiles and adhesive in clean, dry, protected from direct sunlight environment at a minimum temperature of 5°C.
Read installation instructions, warranty and other disclaimers before beginning any installations.
All subfloors must be inspected prior to installation;
Suitable sublfoors: Concrete, Asphalt, Wood, Existing flooring – linoleum or vinyl (as long as it is completely adhered to the subfloor)
All sublfloors must be free from structural defects, smooth, clean, dry and flat;
All subfloors must be free of moisture, dust, salers, paint, primers, curing compounds, parting agents, adhesive removers, hardeners, as well as any solvents, wax, oil, grease, asphalt, gypsum compounds, salts, mold, mildew, or any other materials that may inhibit good adhesion;
All subfloors must have a gradient (2% is suggested) to ensure adequate drainage;
The moisture in the subfloor shall not exceed 4 % and the temperature of the subfloor shall be between 5°C and 30 °C;
- Always install tiles in favourable weather conditions:
Temperatures between +10°C; and +30°C,
Relative Air Humidity not exceeding 65 %.
If the subloor does not meet the above noted requirements, the tiles shall not be installed until the problem has been corrected!
*** It is buyer's responsibility to make sure all surfaces are in suitable condition to ensure good adhesion. ***
Determine Your Layout
Dry Lay rubber tiles so that you have a good idea of what the flooring will look like and to choose your starting place. We recommend laying tiles using a brick – bond pattern in which tiles are staggered in alternating rows to provide long – term stability. To achieve the recommended “brick” pattern, it may be necessary to cut the first and last tiles.
EPOS Two-component PU Adhesive Preparation
The resin component (Comp. A) should be thoroughly stirred to incorporate any slight separation. Whilst stirring, the hardener (comp. B) should be added. Continue stirring until a homogenous mix is obtained. Mixing ratio: 9 (comp A): 1 ( comp B)
Working temperature : Preferably between +10°C and +30°C., higher temperature will reduce the mixture pot life, which is approximately 45 minutes at 20 °C,
25-30 minutes at 30 °C.
Relative Air Humidity: not exceeding 65 %.
Apply adhesive with a suitable, notched trowel evenly only to an area of such size that tile can be set while adhesive is still wet. Set tile in place immediately. Lift a newly set spot occasionally to be sure adhesive is transferring to back. Press tile in firmly with hands.
Work your way across the installation area, setting tiles into adhesive, being aware of mixture’s pot life.
Ensure tiles are fit snugly but not tightly together.
Consumption: 1 kg g/m2, depending on the smoothness of the subfloor.
Do not spill or drip adhesive onto the face of the rubber tiles.
Wet adhesive smears should be removed immediately with a damp cloth.
Always wear gloves.
Let the Floor Cure
Do no place playground equipment, furniture.
Allow traffic or institute general cleaning procedure 48 hours after installation.
Generally accepted installation practices should be followed.
Use of trained installation professionals is recommended for best results.
Cannons UK does not warrant any installation work and specifically disclaims liability for any direct or indirect personal injury, property damage or other costs or losses resulting from incorrect or inadequate installations.
Next day delivery for orders made before 1pm for orders to UK Mainland only. (excludes some parts of Scotland)
Delivery days are Monday-Friday
Orders over 50 mats: We will call first to arrange suitable delivery day.
Next day delivery is never 100% guaranteed although it is around 98% successful.
Free delivery is only for orders over £49.00
Please email firstname.lastname@example.org or call 01379 687768 for prices of any products to be sent outside of the UK Mainland. (including N.I and off shore islands)